Automotive Sandpaper Grit Chart: What Grit to Use Before Painting a Car

At Aozhong, we often receive one question from automotive distributors and repair shops:What grit sandpaper should be used before painting a car? The answer depends on what is being sanded.
Jul 27th,2026 340 ビュー
カタログ

What is the best grit sandpaper to paint a car?

Automotive Sanding A Practical Guide From Body Filler To Final Paint Prep

Painting a car starts long before the spray gun comes out.

Paint does not hide surface defects. It coats the surface below them. Deep sanding scratches, uneven body filler, hard featheredges, primer texture and contaminated existing paint may be visible after the coating cures.

At Aozhong, we are often asked by automotive distributors and repair shops:

What grit sandpaper to use before painting a car?

The answer depends on what you are sanding.

Body filler needs a different grit than primer. Bare metal will require a different process than existing paint. After the paint job, clear coat correction is performed and uses much finer abrasives than pre-paint preparation.

This guide will take you through selecting automotive sandpaper, automotive sanding discs, film abrasives, wet and dry sandpaper and sponge-backed products for each step.

1. What grit sandpaper should I use before painting my car?

Some automotive refinishing processes can use the following ranges as a practical starting point.

Repair Stage Typical Grit Range Main Function
Heavy Paint or Corrosion Removal P40–P80 Removal of damaged coatings or surface corrosion
Body Filler Shaping P60–P80 Fill level and establish panel shape
Body Filler Refinement P120–P180 Scratch removal after coarse shaping
Feathering Repair Edges P180–P240 Blend repair area into existing coating
Prepare Filler Before Primer P240–P320 Surface preparation for primer application
First Sand Primer Surfacer P320–P400 Level primer and identify highs or lows
Final Primer Preparation P400–P600 Ready for sealer or basecoat
Existing Stable Paint Preparation P400–P800 Provide adhesion profile before repainting
Clear Coat Defect Correction P1500–P3000 Removal of dust nibs, texture, or sanding defects
Finishing Polish Refinement P3000–P4000 Reduce polishing time

These are working ranges, not hard and fast rules. The final grit before paint should be according to the technical data sheet of the primer, sealer, basecoat or clear coat used.

2. What Grit of Body Filler Should You Use?

You have to shape body filler first and refine it.

If you use fine sandpaper too soon, the surface will feel smooth but the high and low areas will be wrong. Using coarse sandpaper for too long can leave scratches that will require more primer and more sanding later on.

A typical sequence is:

Step Grain Reason
Preliminary Shaping P60–P80 Remove excess filler and define the panel shape
Scratch Refinement P120 Remove sanding marks from P60 or P80
Surface Refinement P180 Improve transition and reduce scratch depth
Featheredge Prep P240 Blend filler into the surrounding coating
Final Preparation Before Primer P240–P320 Prepare the surface for primer surfacer

An Aozhong ceramic sanding disc or paper-backed sanding disc can provide the material removal required for initial shaping of a filler.

Flat doors, hoods, roofs and quarter panels should be machine sanded and then block sanded. A DA sander will speed things up, but a sanding block is best for checking panel shape.

Why not go from P80 straight to P320?

The P320 may make the surface look finer, but it may not remove the full depth of the P80 scratch pattern.

Any remaining scratches may sometimes show through the primer or paint. A better progression would be:

P80 → P120 → P180 → P240 → P320

Each grit should remove the sanding marks of the preceding grit.

3. What grit should I use before primer?

Before priming, repairs should no longer contain deep shaping scratches.

P240–P320 is a practical final range before primer surfacer for many filler repairs. “The correct choice depends on the primer formulation, repair size and coating system.”

What does the surface need to be before primer?

The repair area shall:

  • no P60 or P80 scratches left;
  • no sharp line between the filler and the existing paint;
  • no loose coating.
  • no sanding dust or contamination;
  • no corrosion left untreated;
  • no highs or lows uncorrected.

Primer can fill small surface marks. It should not be used to mask poor preparation of the filler.

Aozhong multi-hole sanding discs can be used for sanding filler and primer with a compatible extraction system to reduce loading and maintain visibility of the sanding surface.

4. What Grit Should Be Used on Primer Before Paint?

Primer surfacer has two sanding stages: leveling and final paint preparation.

Initial primer leveling

P320–P400 is often used when the primer surface needs to be leveled. A guide coat helps reveal:

  • low areas
  • high areas
  • remaining scratches
  • pinholes
  • primer texture

A sanding block helps maintain panel shape. A hook and loop sanding disc can then be used to refine larger areas.

Final primer preparation

P400–P600 is used in many paint systems before sealer or basecoat.

Primer Task Common Grit Main Concern
Leveling Primer Texture P320–P400 Remove texture without cutting through
Refining Sanding Scratches P400–P500 Remove marks from the leveling stage
Final Preparation Before Basecoat P500–P600 Create a controlled scratch pattern
Edges, Curves, and Blend Areas P600–P800 or scuffing product Reduce cut-through risk

P600 is common before paint, but it is not universal. Metallic colors, blend areas, plastic parts, and some coating systems may require a finer finish.

5. What Grit Should Be Used on Existing Paint Before Repainting?

Existing paint does not always need to be removed.

If the coating is stable, bonded, and free from cracking, lifting, corrosion, or contamination, it can often be sanded and used as part of the repainting substrate.

A common range is P400–P600 for prepared existing paint. Blend areas may use P600–P800 or a suitable non-woven abrasive pad, depending on the coating system.

Existing Surface Condition Suggested Approach
Stable Paint with Light Defects Sand with P400–P600
Blend Area Use P600–P800 or a specified scuffing product
Peeling or Unstable Paint Remove the failed coating
Corrosion Under the Paint Remove paint and treat the substrate
Wax, Silicone, or Polish Residue Clean before sanding
Deep Scratches Repair and prime before basecoat

Sanding does not correct coating failure. Unstable paint should be removed rather than covered.

6. Paper-Backed or Film-Backed Sanding Discs?

The backing affects how the abrasive contacts the panel.

Paper-backed sanding discs

Paper-backed sanding discs are used for filler, primer, paint preparation, and general dry sanding.

They are suitable when cost control and cutting performance are the main requirements.

Film-backed sanding discs

Polyester film provides a base with consistent thickness and resistance to tearing. It is often selected for primer refinement, paint preparation, and other stages where the scratch pattern needs to remain controlled.

Comparison Paper Backing Polyester Film Backing
Typical Use Filler, general primer sanding, dry preparation Primer refinement, paint preparation, finish sanding
Tear Resistance Low High
Surface Consistency Depends on abrasive grade and sanding pressure Provides a more uniform abrasive surface
Wet Sanding Only if designed for wet use Can be used wet if the product structure is waterproof
Cost per Disc Less expensive More expensive
Good for Edges Can tear under tension Harder to tear
Primary Limitation Edge damage and moisture sensitivity May not be necessary for rough sanding

Aozhong purple polyester film sanding discs are good for process backing stability and scratch control.

Paper discs are still handy for filler shaping and general preparation. Not every stage uses film discs.

7. When to use wet and dry sand paper?

Wet sanding is typically done after the coating is on, not to shape filler.

Aozhong wet and dry sandpaper is suitable for primer refinement where the coating system allows it, as well as clear coat defect correction and polishing preparation.

Surface or Defect First Grit Next Step
Small Dust Nib P2000 Refine with P3000 and polish
Light Clear Coat Texture P2000 P3000–P4000, then polish
Moderate Orange Peel P1500 P2000, P3000, then polish
Run or Sag P1000–P1500 only if justified Refine through P2000 and P3000
Pre-Polish Finishing P3000–P4000 Compound and polish

Wet sanding requires clean water, even pressure and a clean abrasive surface. Deep random scratches can be caused by trapped particles or contaminated water.

Don't skimp on wet sanding body filler. Any residual moisture in a repair may affect subsequent coating.

8. What is the purpose of sponge backed abrasives?

Automotive panels are curves, body lines, bumpers, edges and transitions. These surfaces may not have a hard backing applied evenly.

Aozhong Sponge-backed abrasives and sanding sponges apply pressure across curved and contoured surfaces.

They can be used as:

  • bumper radius curves;
  • edges of the door;
  • body lines;
  • primer changes;
  • areas to merge;
  • clear coat polishing;
  • hand sanding in tight spots.

Product Form Main Application Limitation
Firm Sanding Block Flat panels and shaping filler Doesn’t follow curves
Sponge Sanding Block Curves, edges, and hand finishing Not for heavy levelling
Foam-Backed Sanding Disc Fine sanding of contours Can follow low areas instead of levelling them
Standard Sanding Disc Machine sanding on large areas Take care near edges and body lines

Foam or sponge backings can enhance the contact with the surface, but they do not replace grit progression or operator control.

9. Why are multi-hole sanding discs important?

Dust from filler and primer can settle between the abrasive and the panel.

When the disc gets clogged, it can:

  • refrain from cutting;
  • produce heat;
  • leave pigtail scratches;
  • drag particles over the panel;
  • shorten the life of abrasives;
  • decrease visibility.

Compatible with the backing pad and dust collection system of the Aozhong multi-hole sanding discs.

The hole pattern needs to match the sanding pad. If the pad and vacuum path are blocked or incompatible a disc with more holes won't improve extraction.

For dry sanding the system should be checked as a whole:

  1. Sanding pad;
  2. support pad;
  3. hole alignment .
  4. suction hose;
  5. dust collector; 
  6. pressure of operator.

10. Dry Sanding vs Wet Sanding Before Painting?

Most of the filler and primer work is dry-sanded. Wet sanding is used on selected fine-finishing and correction steps.

Method Common Use Advantages Limitations
Dry Sanding Filler, primer, and existing paint preparation Faster removal, guide coat visibility, and dust extraction compatibility Generates airborne dust and can clog
Wet Sanding Clear coat correction and fine refinement Controls dust and helps refine fine scratches Requires cleaning, drying, and water control
Sponge Sanding Curves, edges, and hand finishing Distributes pressure and conforms to contours Does not provide firm levelling

Dry sanding with dust extraction is the main process in most car paint prep. Wet sanding is used more often after clear coat or at some certain fine preparation steps.

11. Recommended Aozhong Sand Process

The following workflow is a general guideline. The final grit should be according to the coating technical data sheet.

Small body filler jobs

Step Product Grit
Shape Filler Ceramic or paper-backed sanding disc P80
Coarse Scratches Removal Sanding disc P120
Refine Filler Sanding disc or sanding strip P180
Feather Repair Edge Film or paper sanding disc P240
Primer Preparation Film sanding disc P320
Primer Level Guide coat and multi-hole sanding disc P400
Final Paint Prep Film sanding disc P500–P600

Surface Preparation Before Painting

Step Product Grit / Grain
Clean and Inspect Coating Cleaning and degreasing products —
Eliminate Defects Paper or film sanding disc P320–P400
Prepare Stable Paint Film sanding disc P400–P600
Prepare Blend Area Sponge abrasive or non-woven pad P600–P800 equivalent, as directed
Clean Before Painting Cleaning of dust and surfaces —

Paint Correction After Clear Coat

Step Product Grit
Level Defect Wet & dry or sponge-backed abrasive P1500–P2000
Scratch Pattern Refinement Sponge-backed abrasive P3000
Polishing Marks Removal Fine abrasive P3000–P4000
Restore Shine Compound and polish —

12. Common Mistakes When Sanding a Car Before Painting

Skip from P80 to P320

P320 does not completely remove P80 scratches. Use medium grits such as P120 and P180.

Sanding filler with fine sand paper

Fine grit follows the surface, and will polish high areas and not level them. Shape with P60-P80 first.

Worn sanding discs.

A worn disc is not a controlled finer grit. It can generate heat and leave uneven scratches.

Ignoring the backing pad.

Old pad can cause uneven contact, pigtails, vibration or disc movement.

Pressure Overload

Pressure adds heat and loading. Allow the abrasive grain to cut.

Sanding over contamination

Wax, silicone, polishing compound, dust and loose particles can cause problems with adhesion or random scratches.

Fill Deep Scratches with Primer

Primer surfacer can fill small sanding marks. It can’t fix bad body filler prep or deep coarse scratches consistently.

FAQ

FAQ Answer
What grit of sandpaper should I use before painting a car? P400–P600 is a common final primer preparation range for many paint systems. The correct grit depends on the primer, base coat, color, sealer, and the coating manufacturer’s technical data sheet.
Is P320 good before car paint? P320 is most often used on primer or primer surfacer before a second stage of primer or sealer. It may be too rough as the final surface for some base coat systems.
Is P600 okay to use before painting a car? In many automotive refinishing systems, P600 is often used for final primer preparation. Always follow the coating manufacturer’s instructions.
What grit of sandpaper should I use on body filler? Use P60–P80 for shaping, P120–P180 for refinement, and P240–P320 before primer where applicable.
If I sand with P400, can I paint over the sanding scratches? Some paint and sealer systems allow preparation to P400. Others require P500, P600, or finer. Check the technical data sheet before painting.
What grit should I use on old paint before repainting? P400–P600 is typical for stable existing paint. Blend areas may need P600–P800 or a specified scuffing product.
Should primer be wet sanded or dry sanded? Many repair shops dry sand primer because it works well with guide coat and dust extraction. Some primer systems are wet sandable. Follow the primer technical data sheet.
What grit should I use for wet sanding clear coat? P1500–P2000 is a common starting point for clear coat correction. Then P3000–P4000 can refine the surface before polishing.
Can I skip sanding grits? Large jumps in grit can leave scratches that may show through primer or paint. Each grit should remove the marks left by the previous grade.
Paper or film sanding discs for automotive paint preparation? Paper-backed discs are suitable for filler and general sanding. Film sanding discs are often used for primer finishing, paint preparation, and processes that require more consistent scratch patterns.

Summary

No one sandpaper grit will get you through all the stages of painting a car.

  • P60-P80 make body filler.
  • P120-P180 will remove the coarse filler scratches.
  • Primer Prep Repair P240 – P320.
  • P400–P600 prepares many primer paint systems.
  • P1500-P3000 clear coat repair after painting.

At Aozhong we choose the abrasive depending on the layer to be sanded, the necessary removal of material, the shape of the panel, the sanding method and the subsequent coating stage.

The complete automotive sanding process can involve paper-backed sanding discs, polyester film sanding discs, multi-hole discs, wet and dry sandpaper, sponge-backed abrasives, sanding blocks, and non-woven products.

The idea here is not to go with the finest grit you can get. The goal is to use a grit that will remove the previous scratch pattern without creating a new problem for the next step.

Leave a message
お名前 *
メールアドレス *
会社名
お問い合わせ内容・ご希望の製品仕様